Steel Nails From 5 Countries: New AD/CVD Investigations Deadlines and Scope

The Commerce Department issued Federal Register notices on its recently initiated antidumping investigations on steel nails from India, Sri Lanka, Thailand and Turkey (A-533-904, A-542-804, A-549-844, A-489-846) and countervailing duty investigations on steel nails from India, Oman, Sri Lanka, Thailand and Turkey (C-533-905, C-523-817, C-542-805, C-549-845, C-489-847).

The International Trade Commission will conduct a concurrent investigation to determine whether imports of dumped and illegally subsidized steel nails are injuring U.S. industry. If the ITC finds no injury in its preliminary injury determination, due Feb. 14, the investigations will immediately end. If Commerce finds dumping or illegal subsidization in the preliminary determinations of these investigations, due in March for CV duties and June for AD duties, it will set AD and/or CV duty cash deposit requirements for imports of merchandise subject to the investigation. If both Commerce and the ITC reach affirmative final determinations, Commerce will issue an AD and/or CV duty order making duties permanent and beginning a process of annual administrative reviews to set final assessments of AD/CV duties on importers and potentially change AD/CV duty cash deposit rates.

AD/CVD Respondent Selection

Commerce said it will rely on CBP data to pick the respondents for the CVD investigations and for all of the AD duty investigations. Parties wishing to comment regarding the CBP data and respondent selection must do so within three business days of the publication date of the notice of initiation of these CVD and AD investigations, i.e., Jan. 31.

Scope of the AD/CVD Investigations

"The merchandise covered by these investigations is certain steel nails having a nominal shaft or shank length not exceeding 12 inches. Certain steel nails include, but are not limited to, nails made from round wire and nails that are cut from flat-rolled steel or long-rolled flat steel bars. Certain steel nails may be of one piece construction or constructed of two or more pieces. Examples of nails constructed of two or more pieces include, but are not limited to, anchors comprised of an anchor body made of zinc or nylon and a steel pin or a steel nail; crimp drive anchors; split-drive anchors, and strike pin anchors. Also included in the scope are anchors of one piece construction.

"Certain steel nails may be produced from any type of steel, and may have any type of surface finish, head type, shank, point type and shaft diameter. Finishes include, but are not limited to, coating in vinyl, zinc (galvanized, including but not limited to electroplating or hot dipping one or more times), phosphate, cement, and paint. Certain steel nails may have one or more surface finishes. Head styles include, but are not limited to, flat, projection, cupped, oval, brad, headless, double, countersunk and sinker. Shank or shaft styles include, but are not limited to, smooth, barbed, screw threaded, ring shank and fluted.

"Screw-threaded nails subject to this proceeding are driven using direct force and not by turning the nail using a tool that engages with the head. Point styles include, but are not limited to, diamond, needle, chisel and blunt or no point. Certain steel nails may be sold in bulk, or they may be collated in any manner using any material.

"Excluded from the scope are certain steel nails packaged in combination with one or more non-subject articles, if the total number of nails of all types, in aggregate regardless of size, is less than 25. If packaged in combination with one or more non-subject articles, certain steel nails remain subject merchandise if the total number of nails of all types, in aggregate regardless of size, is equal to or greater than 25, unless otherwise excluded based on the other exclusions below.

"Also excluded from the scope are certain steel nails with a nominal shaft or shank length of one inch or less that are a component of an unassembled article, where the total number of nails is sixty (60) or less, and the imported unassembled article falls into one of the following eight groupings: (1) Builders' joinery and carpentry of wood that are classifiable as windows, French-windows and their frames; (2) builders' joinery and carpentry of wood that are classifiable as doors and their frames and thresholds; (3) swivel seats with variable height adjustment; (4) seats that are convertible into beds (with the exception of those classifiable as garden seats or camping equipment); (5) seats of cane, osier, bamboo or similar materials; (6) other seats with wooden frames (with the exception of seats of a kind used for aircraft or motor vehicles); (7) furniture (other than seats) of wood (with the exception of (i) medical, surgical, dental or veterinary furniture; and (ii) barbers' chairs and similar chairs, having rotating as well as both reclining and elevating movements); or (8) furniture (other than seats) of materials other than wood, metal, or plastics ( e.g., furniture of cane, osier, bamboo or similar materials). The aforementioned imported unassembled articles are currently classified under the following Harmonized Tariff Schedule of the United States (HTSUS) subheadings: 4418.10, 4418.20, 9401.30, 9401.40, 9401.51, 9401.59, 9401.61, 9401.69, 9403.30, 9403.40, 9403.50, 9403.60, 9403.81 or 9403.89.

"Also excluded from the scope of these investigations are nails suitable for use in powder-actuated hand tools, whether or not threaded, which are currently classified under HTSUS subheadings 7317.00.2000 and 7317.00.3000.

"Also excluded from the scope of these investigations are nails suitable for use in gas-actuated hand tools. These nails have a case hardness greater than or equal to 50 on the Rockwell Hardness C scale (HRC), a carbon content greater than or equal to 0.5 percent, a round head, a secondary reduced-diameter raised head section, a centered shank, and a smooth symmetrical point.

"Also excluded from the scope of these investigations are corrugated nails. A corrugated nail is made up of a small strip of corrugated steel with sharp points on one side.

"Also excluded from the scope of these investigations are thumb tacks, which are currently classified under HTSUS subheading 7317.00.1000.

"Also excluded from the scope are decorative or upholstery tacks.

"Certain steel nails subject to these investigations are currently classified under HTSUS subheadings 7317.00.5501, 7317.00.5502, 7317.00.5503, 7317.00.5505, 7317.00.5507, 7317.00.5508, 7317.00.5511, 7317.00.5518, 7317.00.5519, 7317.00.5520, 7317.00.5530, 7317.00.5540, 7317.00.5550, 7317.00.5560, 7317.00.5570, 7317.00.5580, 7317.00.5590, 7317.00.6530, 7317.00.6560 and 7317.00.7500. Certain steel nails subject to these investigations also may be classified under HTSUS subheadings 7318.15.5060, 7318.15.5090, 7907.00.6000, 8206.00.0000 or other HTSUS subheadings. While the HTSUS subheadings are provided for convenience and customs purposes, the written description of the scope of these investigations is dispositive."

Comments on the scope are due by Feb. 8.

Investigations Timetable

These deadlines may be, and usually are, extended. The Commerce Department fact sheet on the initiation of these investigations is here. See 2201040030 for a summary of the Commerce Department's receipt of the petition underlying the initiation of this investigation.