New AD/CV Duties Requested on Steel Nails From India, Sri Lanka, Thailand, Turkey and Oman
A U.S. manufacturer seeks the imposition of new antidumping and countervailing duties on steel nails from India, Sri Lanka, Thailand and Turkey, as well as new CV duties on steel nails from Oman, it said in petitions filed with the Commerce Department and the International Trade Commission Dec. 30. Commerce will now decide whether to begin AD/CVD investigations, which could result in the imposition of permanent AD/CV duty orders and the assessment of AD and CV duties on importers.
CV duties on Oman sought by the petition would come on top of an existing AD duty order on steel nails from Oman in place since 2015. Existing AD/CVD orders are also in place on steel nails from China, the United Arab Emirates, Malaysia, South Korea, Taiwan and Vietnam. Commerce and the ITC also investigated steel nails from India and Turkey in 2014 but ended those investigations after the ITC found imports from those two countries were negligible.
The scope of these investigations would be similar to the scope of existing ADD/CVD orders on steel nails from South Korea, Malaysia, Oman, Taiwan and Vietnam. However, unlike the scopes of those orders, the proposed scope of these investigations would include "roofing" nails that meet the specifications of Type I, Style 20 nails as identified in Tables 29 through 33 of ASTM Standard F1667, as well as masonry anchors of one- or two-piece construction. Upholstery and decorative tacks, on the other hand, would be excluded from the scope.
Proposed Scope
The petition proposes the following scope for the investigations:
The merchandise covered by this investigation is certain steel nails having a nominal shaft or shank length not exceeding 12 inches. Certain steel nails include, but are not limited to, nails made from round wire and nails cut from flat-rolled steel or long-rolled flat steel bars. Certain steel nails may be of one-piece construction or constructed of two or more pieces. Examples of nails constructed of two or more pieces include, but are not limited to, masonry anchors comprised of an anchor made of zinc or nylon and a steel nail; zinc anchors; crimp-drive anchors; split-drive anchors, and strike pin anchors. Also included in the scope are anchors of one-piece construction.
Certain steel nails may be produced from any type of steel, and may have any type of surface finish, head type, shank, point type and shaft diameter. Finishes include, but are not limited to, coating in vinyl, zinc (galvanized, including but not limited to electroplating or hot dipping one or more times), phosphate, cement and paint. Certain steel nails may have one or more surface finishes. Head styles include, but are not limited to, flat, projection, cupped, oval, brad, headless, double, countersunk and sinker. Shank or shaft styles include, but are not limited to, smooth, barbed, screw threaded, ring shank and fluted.
Screw-threaded nails subject to this proceeding are driven using direct force and not by turning the nail using a tool that engages with the head. Point styles include, but are not limited to, diamond, needle, chisel and blunt or no point. Certain steel nails may be sold in bulk, or they may be collated in any manner using any material.
Excluded from the scope are certain steel nails packaged in combination with one or more non-subject articles, if the total number of nails of all types, in aggregate regardless of size, is less than 25. If packaged in combination with one or more non-subject articles, certain steel nails remain subject merchandise if the total number of nails of all types, in aggregate regardless of size, is equal to or greater than 25, unless otherwise excluded based on the other exclusions below.
Also excluded from the scope are certain steel nails with a nominal shaft or shank length of one inch or less that are (a) a component of an unassembled article, (b) the total number of nails is sixty (60) or fewer, and (c) the imported unassembled article falls into one of the following eight groupings: (1) Builders’ joinery and carpentry of wood that are classifiable as windows, French-windows and their frames; (2) builders’ joinery and carpentry of wood that are classifiable as doors and their frames and thresholds; (3) swivel seats with variable height adjustment; (4) seats that are convertible into beds (with the exception of those classifiable as garden seats or camping equipment); (5) seats of cane, osier, bamboo or similar materials; (6) other seats with wooden frames (with the exception of seats of a kind used for aircraft or motor vehicles); (7) furniture (other than seats) of wood (with the exception of (i) medical, surgical, dental or veterinary furniture; and (ii) barbers’ chairs and similar chairs, having rotating as well as both reclining and elevating movements); or (8) furniture (other than seats) of materials other than wood, metal, or plastics (e.g., furniture of cane, osier, bamboo or similar materials). The aforementioned imported unassembled articles are currently classified under the following Harmonized Tariff Schedule of the United States (HTSUS) subheadings: 4418.10, 4418.20, 9401.30, 9401.40, 9401.51, 9401.59, 9401.61, 9401.69, 9403.30, 9403.40, 9403.50, 9403.60, 9403.81 or 9403.89.
Also excluded from the scope of this investigation are nails suitable for use in powder-actuated handtools, whether or not threaded, which are currently classified under HTSUS subheadings 7317.00.20.00 and 7317.00.30.00.
Also excluded from the scope of this investigation are nails having a case hardness greater than or equal to 50 on the Rockwell Hardness C scale (HRC), a carbon content greater than or equal to 0.5 percent, a round head, a secondary reduced-diameter raised head section, a centered shank, and a smooth symmetrical point, suitable for use in gas-actuated hand tools.
Also excluded from the scope of this investigation are corrugated nails. A corrugated nail is made up of a small strip of corrugated steel with sharp points on one side.
Also excluded from the scope of this investigation are thumb tacks, which are currently classified under HTSUS subheading 7317.00.10.00.
Also excluded from the scope are decorative or upholstery tacks.
Certain steel nails subject to this investigation are currently classified under HTSUS subheadings 7317.00.55.02, 7317.00.55.03, 7317.00.55.05, 7317.00.55.07, 7317.00.55.08, 7317.00.55.11, 7317.00.55.18, 7317.00.55.19, 7317.00.55.20, 7317.00.55.30, 7317.00.55.40, 7317.00.55.50, 7317.00.55.60, 7317.00.55.70, 7317.00.55.80, 7317.00.55.90, 7317.00.65.30, 7317.00.65.60 and 7317.00.75.00. Certain steel nails subject to this investigation also may be classified under HTSUS subheadings 7907.00.60.00, 8206.00.00.00 or other HTSUS subheadings. While the HTSUS subheadings are provided for convenience and customs purposes, the written description of the scope of this investigation is dispositive.
Commerce Accepting Comments on Petition Support
The Commerce Department is accepting comments on domestic industry support for the petitions to determine whether the petitions meet the dual requirements of support by domestic producers or workers accounting for (1) at least 25% of the total production of the domestic-like product and (2) more than 50% of the production of the domestic-like product produced by that portion of the industry expressing support for, or opposition to, the petition. If the petitions meet these requirements, among others, Commerce will initiate antidumping and countervailing duty investigations. Comments are due by Jan. 11.
Email ITTNews@warren-news.com for a copy of the petition.